View MIC2583R-KBQS_347354.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC2582/MIC2583
Micrel
MIC2582/MIC2583
Single Channel Hot Swap Controllers Final
General Description
The MIC2582 and MIC2583 are single channel positive voltage hot swap controllers designed to allow the safe insertion of boards into live system backplanes. The MIC2582 and MIC2583 are available in 8-pin SOIC and 16-pin QSOP packages, respectively. Using a few external components and by controlling the gate drive of an external N-Channel MOSFET device, the MIC2582/83 provide inrush current limiting and output voltage slew rate control in harsh, critical power supply environments. Additionally, a circuit breaker function will latch the output MOSFET off if the current limit threshold is exceeded for a determined period. The MIC2583R option includes an auto-restart function upon detecting an overcurrent condition.
Features
* MIC2582: Pin-for-pin functional equivalent to the LTC1422 * 2.3V to 13.2V supply voltage operation * Surge voltage protection up to 20V * Current regulation limits inrush current regardless of load capacitance * Programmable inrush current limiting * Electronic circuit breaker * Dual-level overcurrent fault sensing eliminates false tripping * Fast response to short circuit conditions (<1s) * Programmable output undervoltage detection * Undervoltage Lockout (UVLO) protection * Auto-restart function (MIC2583R) * Power-On Reset and Power-Good status outputs (Power-Good for the MIC2583 and MIC2583R only) * /FAULT status output (MIC2583 and MIC2583R)
Applications
* * * * * RAID systems Base stations PC board hot swap insertion and removal Hot swap CompactPCI cards Network switches
Typical Application
BACKPLANE PCB EDGE CONNECTOR CONNECTOR VIN 12V **D1 (18V) Long Pin R1 3.3 C1 1F
3
RSENSE 0.006 2% 2 1
4
Q1 Si7892DP (PowerPAKTM SO-8)
VOUT 12V@6A CLOAD 500F
16
15
VCC Short Pin
3
SENSE
GATE ON DIS PWRGD
11
14
R2 76.8k 1% R3 R4 9.76k 47k 1% /FAULT Signal Medium (or Short) Pin
C2 0.01F
13
R5 93.1k 1% VIN R7 47k
VIN R8 47k
DOWNSTREAM CONTROLLER
MIC2583/83R
2
Power-Good Output
1
EN /RESET
FAULT
/POR FB CPOR
4
Power-On Reset Output
12
GND
7, 8
CFILTER
5
Long Pin GND
C3 0.1F
C4 8200pF
R6 12.4k 1%
*Undervoltage (Input) = 10.5V *Undervoltage (Output) & Power-Good (Output) = 11.0V *START-UP Delay = 12ms */POR Delay = 50ms *Circuit Breaker Response Time = 1.5ms **D1 is BZX84C18 *(See Functional Description and Applications Information)
Figure 1. MIC2583/83R Typical Application Circuit
Micrel, Inc. * 1849 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 944-0970 * http://www.micrel.com
April 2003
1
MIC2582/MIC2583
MIC2582/MIC2583
Micrel
Ordering Information
Part Number MIC2582-JBM MIC2583-xBQS Fast Circuit Breaker Threshold 100mV x = J, 100mV x = K, 150mV x = L, 200mV x = M, Off MIC2583R-xBQS x = J, 100mV x = K*, 150mV x = L*, 200mV x = M*, Off
* Contact factory for availability.
Circuit Breaker Latched off Latched off
Package 8-pin SOIC 16-pin QSOP
Auto-retry
16-pin QSOP
Pin Configuration
/POR 1 PWRGD 2 16 VCC 15 SENSE 14 GATE 13 DIS 12 FB 11 /FAULT 10 NC 9 NC
/POR 1 ON 2 CPOR 3 GND 4
8 VCC 7 SENSE 6 GATE 5 FB
ON 3 CPOR 4 CFILTER 5 NC 6 GND 7 GND 8
8-Pin SOIC (M)
16-Pin QSOP (QS)
MIC2582/MIC2583
2
April 2003
MIC2582/MIC2583
Micrel
Pin Description
Pin Name /POR 8-pin SOIC 1 16-pin QSOP 1 Pin Function Power-On Reset Output: Open drain N-channel device, Active Low. This pin remains asserted during start-up until a time period (tPOR) after the FB pin voltage rises above the power-good threshold (VFB). The timing capacitor CPOR determines tPOR. When the output voltage monitored at the FB pin falls below VFB, /POR is asserted for a minimum of one timing cycle (tPOR). The /POR pin requires a pull-up resistor (10k minimum) to VCC. ON Input: Active High. The ON pin, an input to a Schmitt-triggered comparator used to enable/disable the controller, is compared to a 1.24V reference with 50mV of hysteresis. When a logic high is applied to the ON pin (VON > 1.24V), a start-up sequence begins when the GATE pin starts ramping up towards its final operating voltage. When the ON pin receives a logic low signal (VON < 1.19V), the GATE pin is grounded and /FAULT remains high if VCC is above the UVLO threshold. ON must be low for 20s in order to initiate a start-up sequence. Additionally, toggling the ON pin LOW to HIGH resets the circuit breaker. Power-On Reset Timer: A capacitor connected between this pin and ground sets the supply contact start-up delay (tSTART) and the power-on reset interval (tPOR). When VCC rises above the UVLO threshold, the capacitor connected to CPOR begins to charge. When the voltage at CPOR crosses 0.3V, the start-up threshold (VSTART), a start cycle is initiated if ON is asserted while capacitor CPOR is immediately discharged to ground. When the voltage at FB rises above VFB, capacitor CPOR begins to charge again. When the voltage at CPOR rises above the power-on reset delay threshold (VTH), the timer resets by pulling CPOR to ground, and /POR is de-asserted. If CPOR = 0, then tSTART defaults to 20s. Ground connection: Tie to analog ground. Power-Good Threshold Input (Undervoltage Detect): This input is internally compared to a 1.24V reference with 30mV of hysteresis. An external resistive divider may be used to set the voltage at this pin. If this input momentarily goes below 1.24V, then /POR is activated for one timing cycle, tPOR, indicating an output undervoltage condition. The /POR signal deasserts one timing cycle after the FB pin exceeds the power-good threshold by 30mV. A 5s filter on this pin prevents glitches from inadvertently activating this signal. Gate Drive Output: Connects to the gate of an external N-channel MOSFET. An internal clamp ensures that no more than 9V is applied between the GATE pin and the source of the external MOSFET. The GATE pin is immediately brought low when either the circuit breaker trips or an undervoltage lockout condition occurs. Circuit Breaker Sense Input: A resistor between this pin and VCC sets the current limit threshold. Whenever the voltage across the sense resistor exceeds the slow trip current limit threshold (VTRIPSLOW), the GATE voltage is adjusted to ensure a constant load current. If VTRIPSLOW (50mV) is exceeded for longer than time period tOCSLOW, then the circuit breaker is tripped and the GATE pin is immediately pulled low. If the voltage across the sense resistor exceeds the fast trip circuit breaker threshold, VTRIPFAST, at any point due to fast, high amplitude power supply faults, then the GATE pin is immediately brought low without delay. To disable the circuit breaker, the SENSE and VCC pins can be tied together. The default VTRIPFAST for either device is 100mV. Other fast trip thresholds are available: 150mV, 200mV, or OFF (VTRIPFAST disabled). Please contact factory for availability of other options. Positive Supply Input: 2.3V to 13.2V. The GATE pin is held low by an internal undervoltage lockout circuit until VCC exceeds a threshold of 2.2V. If VCC exceeds 13.2V, an internal shunt regulator protects the chip from transient voltages up to 20V at the VCC and SENSE pins.
ON
2
3
CPOR
3
4
GND FB
4 5
7,8 12
GATE
6
14
SENSE
7
15
VCC
8
16
April 2003
3
MIC2582/MIC2583
MIC2582/MIC2583
Pin Name PWRGD 8-pin SOIC N/A 16-pin QSOP 2 Pin Function
Micrel
Power-Good Output: Open drain N-channel device, Active High. When the voltage at the FB pin is lower than 1.24V, PWRGD output is held low. When the voltage at the FB pin exceeds 1.24V, then PWRGD is asserted immediately. The PWRGD pin requires a pull-up resistor (10k minimum) to VCC. Current Limit Response Timer: A capacitor connected to this pin defines the period of time (tOCSLOW) in which an overcurrent event must last to signal a fault condition and trip the circuit breaker. If no capacitor is connected, then tOCSLOW defaults to 5s. Circuit Breaker Fault Status Output: Open drain N-channel device, Active Low. The /FAULT pin is asserted when the circuit breaker trips due to an overcurrent condition or when an undervoltage lockout condition exists. The /FAULT pin requires a pull-up resistor (10k minimum) to VCC. Discharge Output: When the MIC2583/83R is turned off, a 500 internal resistor at this output allows the discharging of any load capacitance to ground. No internal connection.
CFILTER
N/A
5
/FAULT
N/A
11
DIS NC
N/A N/A
13 6,9,10
MIC2582/MIC2583
4
April 2003
MIC2582/MIC2583
Micrel
Absolute Maximum Ratings (Note 1)
All voltages are referred to GND Supply Voltage (VCC) .................................... -0.3V to 20V /POR, /FAULT, PWRGD pins ....................... -0.3V to 15V SENSE pin ........................................... -0.3V to VCC+0.3V ON pin .................................................. -0.3V to VCC+0.3V GATE pin ...................................................... -0.3V to 20V FB input pins ................................................... -0.3V to 6V Junction Temperature .............................................. 125C ESD Rating ........................................................................ Human body model ............................................... 2kV Machine model .................................................... 100V Electrical Characteristics (Note 3)
Symbol VCC ICC VTRIP Parameter Supply Voltage Supply Current Circuit Breaker Trip Voltage (Current Limit Threshold) VON = 2V Condition
Operating Ratings (Note 2)
Supply Voltage (VCC) ................................... 2.3V to 13.2V Thermal Resistance (R(J-A)) 8-pin SOIC ........................................................ 163C/W 16-pin QSOP .................................................... 112C/W Operating Temperature Range ................. -40C to +85C
VCC = 5.0V, TA = 25C unless otherwise noted. Bold values indicate -40C TA +85C. Min 2.3 1.5 VTRIPSLOW VTRIPFAST (MIC2582) VTRIPFAST x = J (MIC2583/83R) x = K x=L VGS IGATE IGATEOFF External Gate Drive VGATE - VCC VCC > 3V VCC = 2.3V GATE Pin Pull-Up Current Start Cycle, VGATE = 0V, VCC =13.2V VCC = 2.3V GATE Pin Sink Current VGATE >1V /FAULT = 0 (MIC2583/83R only) ITIMER ICPOR VTH VUV VUVHYS VON VONHYS ION VSTART VAUTO IAUTO Current Limit/Overcurrent Timer (CFILTER) Current (MIC2583/83R) Power-On-Reset Timer Current VCC = 13.2V, Note 4 VCC = 2.3V, Note 4 Turn off -8.5 4.5 -3.5 0.5 1.19 2.1 1.90 85 130 175 7 3.5 -30 -26 42 50 100 100 150 200 8 4.8 17 17 100 50 110 -6.5 6.5 2.5 1.3 1.245 2.2 2.05 150 ON rising ON falling ON Pin Hysteresis ON Pin Input Current Start-Up Delay Timer Threshold Auto-Restart Threshold Voltage (MIC2583R only) Auto-Restart Current (MIC2583R only) VON = VCC VCPOR rising upper threshold lower threshold charge current discharge current 0.26 1.19 0.26 10 0.31 1.24 0.31 13 1.4 1.19 1.14 1.24 1.19 50 -0.5 0.36 1.30 0.36 16 2 1.29 1.24 1.30 2.3 2.20 -4.5 8.5 -1.5 110 170 225 9 6.5 -8 -8 Typ Max 13.2 2.5 59 Units V mA mV mV mV mV mV V V A A mA mA A A A A mA V V V mV V V mV A V V V A A
VTRIP = VCC - VSENSE
VCC - VSENSE > VTRIPSLOW (timer on) VCC - VSENSE < VTRIPSLOW (timer off) timer on timer off
POR Delay and Overcurrent Timer (CFILTER) Threshold Undervoltage Lockout Threshold
VCPOR rising VCFILTER rising (MIC2583/83R only) VCC rising VCC falling
Undervoltage Lockout Hysteresis ON Pin Threshold Voltage
April 2003
5
MIC2582/MIC2583
MIC2582/MIC2583
Symbol VFB VFBHYS VOL Parameter Power-Good Threshold Voltage Condition FB rising FB falling FB Hysteresis /POR, /FAULT, PWRGD Output Voltage (/FAULT, PWRGD MIC2583/83R only) Output Discharge Resistance (MIC2583/83R only) IOUT = 1mA Min 1.19 1.15 Typ 1.24 1.20 40 0.4 Max 1.29 1.25
Micrel
Unit V V mV V
RDIS
500
1000
s
AC Parameters (Note 4) tOCFAST Fast Overcurrent SENSE to GATE Low Trip Time VCC = 5V VCC - VSENSE = 100mV CGATE = 10nF Figure 2 VCC = 5V, VCC - VSENSE = 50mV CFILTER = 0 Figure 2 1
tOCSLOW
Slow Overcurrent SENSE to GATE Low Trip Time ON Delay Filter FB Delay Filter
5
s
tONDLY tFBDLY
Note 1. Note 2. Note 3. Note 4.
20 20
s s
Exceeding the absolute maximum rating may damage the device. The device is not guaranteed to function outside its operating rating. Specification for packaged product only. Not a tested parameter, guaranteed by design.
Timing Diagrams
VTRIPFAST 50mV (VCC - VSENSE) tOCSLOW GATE 1V 1V tOCFAST
Figure 2. Current Limit Response
1.2V FB tPOR 1.5V /POR
1.5V /PWRGD
Figure 3. Power-On Reset Response
VUVLO VCC tSTART 1V VGATE
Figure 4. Power-On Start-Up Delay Timing MIC2582/MIC2583 6 April 2003
MIC2582/MIC2583
Micrel
Typical Characteristics
Voltage Threshold (VTH) vs. Temperature
VOLTAGE THRESHOLD (V)
ON PIN THRESHOLD (V)
ON Pin Threshold vs. Temperature (Upper Threshold)
1.300
ON PIN THRESHOLD (V)
ON Pin Threshold vs. Temperature (Lower Threshold)
1.240 1.230 VCC = 5.0V 1.220 1.210 1.200 1.190 1.180 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) VCC = 13.2V VCC = 2.3V
1.300 1.290 1.280 1.270 1.260 1.250 1.240 1.230 1.220 1.210 VCC = 13.2
1.290 1.280 1.270 1.260 1.250 1.240 1.230 1.220 1.210
VCC = 13.2
VCC = 2.3
VCC = 5.0
VCC = 2.3
VCC = 5.0
1.200 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
1.200 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
IGATE(OFF) vs. Temperature
GATE CURRENT-OFF (A) GATE CURRENT-ON (A) 150 140 130 120 110 100 90 80 70 60 50 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) VCC = 2.3V VCC = 13.2V -30 -25 -20 -15 -10 -5
IGATE(ON) vs. Temperature
PWRGD THRESHOLD (V)
1.300 1.275 1.250 1.225 1.200 1.175 1.150 1.125
Power-Good Threshold vs. Temperature (Increasing)
VCC = 13.2V
VCC = 13.2V
VCC = 5.0V
VCC = 5.0V
VCC = 2.3V
VCC = 5.0V
VCC = 2.3V
0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
1.100 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
Power-Good Threshold vs. Temperature (Decreasing)
AUTO-RESTART THRESHOLD (V) PWRGD THRESHOLD (V)
Auto-Restart Threshold Voltage vs. Temperature (Lower) MIC2583R
0.500 0.450 0.400 0.350 0.300 VCC = 2.3V 0.250 VCC = 5.0V VCC = 13.2V
AUTO-RESTART THRESHOLD (V)
Auto-Restart Threshold Voltage vs. Temperature (Upper) MIC2583R
1.400 1.350 1.300 1.250 1.200 V = 2.3V CC 1.150 1.100 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) VCC = 5.0V VCC = 13.2V
1.300 1.280 1.260 1.240 1.220 1.200 VCC = 2.3V
1.180 1.160 VCC = 13.2V 1.140 1.120
VCC = 5.0V
1.100 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
0.200 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
Current-Limit Timer Current vs. Temperature
-8.0 UVLO THRESHOLD (V) TIMER CURRENT (A) -7.5 -7.0 -6.5 -6.0 -5.5 VCC = 5.0V VCC = 2.3V VCC = 13.2V 2.50 2.40 2.30 2.20 2.10 2.00 1.90 1.80 1.70
UVLO Threshold vs. Temperature
UVLO+
Gate Voltage vs. Temperature
20 18 GATE VOLTAGE (V) 16 14 12 10 8 6 4 VCC = 2.3V VCC = 5.0V VCC = 12.0V
UVLO-
-5.0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
1.60 1.50 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
2 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
April 2003
7
MIC2582/MIC2583
MIC2582/MIC2583
Micrel
Circuit Breaker Slow (VTRIP) vs. Temperature
55
SLOW THRESHOLD (mV) FAST THRESHOLD (mV)
120 110 100
Circuit Breaker Fast (VTRIP) vs. Temperature
POR TIMER CURRENT (A)
Power-On Reset Timer Current vs. Temperature
4.0 3.5 3.0 2.5 2.0 VCC = 13.2V 1.5 VCC = 5.0V VCC = 2.3V
VCC = 2.3V VCC = 13.2V
54 53 52 51 50 49 48 47
VCC = 5.0V VCC = 2.3V
90 80 VCC = 5.0V 70 60 50 40
VCC = 13.2V
46 45 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
30 20 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
1.0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
20 18 16 CURRENT (A) 14 12 10 8 6 4 2 0
Gate Current vs. Gate Voltage @ -40C
VCC = 13.2V CURRENT (A)
18 16 14 12 10 8 6 4 2 0
Gate Current vs. Gate Voltage @ 25C
16 14 CURRENT (A)
Gate Current vs. Gate Voltage @ 85C
VCC = 13.2V
12 10 8 6 4 2 0
VCC = 13.2V VCC = 2.3V
VCC = 5.0V
VCC = 2.3V VCC = 5.0V 0 2 4 6 8 10 12 14 16 18 20 VOLTAGE (V)
VCC = 2.3V 0 2 4 6 8 10 12 14 16 18 20 VOLTAGE (V)
VCC = 5.0V 0 2 4 6 8 10 12 14 16 18 20 VOLTAGE (V)
MIC2582/MIC2583
8
April 2003
MIC2582/MIC2583
Micrel
Test Circuit
IIN +
3
RSENSE 0.025
1 2 4
IRF7413 or equivalent
IOUT +
100k VIN
CIN VCC SENSE GATE CGATE FB
CLOAD RLOAD
VOUT
- R1
- ON
DUT
12.4k 1%
Figure 5. Applications Test Circuit (not all pins shown for simplicity)
April 2003
9
MIC2582/MIC2583
MIC2582/MIC2583
Micrel
Functional Characteristics (See Figure 5, Applications Test Circuit)
Turn On - VOUT = 12V
Turn Off - VOUT = 12V
VOUT 5V/div
ON 5V/div
VOUT PWRGD 5V/div 5V/div
PWRGD 5V/div
ON 5V/div
IIN 500mA/div
TIME (10ms/div.)
IIN 500mA/div
CIN = 4.7F CLOAD = 100F CGATE = 47nF RLOAD = 12 R1 = 100k
CIN = 4.7F CLOAD = 100F CGATE = 47nF RLOAD = 12 R1 = 100k TIME (1ms/div.)
Turn On - VOUT = 5V
Turn Off - VOUT = 5V
PWRGD VOUT 5V/div 2V/div
ON 2V/div
IIN VOUT 500mA/div 2V/div
PWRGD 2V/div
ON 2V/div
IIN 500mA/div
CIN = 4.7F CLOAD = 100F CGATE = 47nF RLOAD = 5 R1 = 33k TIME (5ms/div.)
CIN = 4.7F CLOAD = 100F CGATE = 47nF RLOAD = 5 R1 = 33k TIME (1ms/div.)
Turn On (CGATE = 0) - VOUT = 5V (MIC2583)
ON 5V/div
Inrush Current Response - VOUT = 5V
GATE 5V/div
ON 5V/div
VOUT 2V/div
VOUT 2V/div
FAULT 5V/div
IOUT 500mA/div
TIME (250s/div.)
IIN 500mA/div
CIN = 4.7F CGATE = 0 CLOAD = 10F RLOAD = 5 R1 = 33k
CIN = 0.1F CLOAD = 100F CGATE = 10nF RLOAD = 5 R1 = 33k TIME (2.5ms/div.)
MIC2582/MIC2583
10
April 2003
MIC2582/MIC2583
Micrel
Functional Characteristics (See Figure 5, Applications Test Circuit)
Turn On Into Heavy Load - VOUT = 12V
FAULT CFILTER ON 10V/div 1V/div 5V/div CFILTER ON 1V/div 5V/div
Turn On Into Short Circuit - VOUT = 5V
IIN 500mA/div
TIME (20ms/div.)
IIN 500mA/div
CIN = 4.7F CGATE = 0 CLOAD = 100F CFILTER = 100nF RLOAD = 6 ILIM = 1.7A R1 = 100k
GATE 2V/div
1.85A
CGATE = CLOAD = 0 CFILTER = 100nF CIN = 4.7F ILIM = 1.7A R1 = 33k
TIME (2.5ms/div.)
Shutdown by Short Circuit - VOUT = 5V (MIC2583)
FAULT 5V/div GATE 5V/div
IOUT 500mA/div
CGATE = 0 CIN = 4.7F CLOAD = 10F RLOAD = 5 ILIM = 3.3A R1 = 33k
TIME (100s/div.)
April 2003
11
MIC2582/MIC2583
MIC2582/MIC2583
Micrel
Functional Diagram
MIC2583/83R
SENSE VCC
15(7) 16(8)
+ - 50mV + - VCC 6.5A 100mV ITIMER UVLO 2.2V
Charge Pump 9V 21V 500
Circuit Breaker Trips or UVLO
14(6)
GATE
13
DIS
11 5
/FAULT
CFILTER 6.5A VREF
+ -
Logic
1(1)
/POR GND FB
7,8(4)
12(5)
VREF VCC 2.5A CPOR
4 (3)
+ -
Glitch Filter
2
PWRGD
ICPOR 0.3V + - + - Glitch Filter + - 1.24V Reference
3(2)
ON
VREF
VREF
Pin numbers for MIC2582 are in parenthesis ( ) where applicable
MIC2582/MIC2583
12
April 2003
MIC2582/MIC2583
Micrel
supply is already present (i.e., not a "hot swapping" condition) and the MIC2582/83 device is enabled by applying a logic high signal at the ON pin, the GATE output begins ramping immediately as the first CPOR timing cycle is bypassed. Active current regulation is employed to limit the inrush current transient response during start-up by regulating the load current at the programmed current limit value (See Current Limiting and DualLevel Circuit Breaker section). The following equation is used to determine the nominal current limit value:
V 50mV ILIM = TRIPSLOW = RSENSE RSENSE
Functional Description
Hot Swap Insertion When circuit boards are inserted into live system backplanes and supply voltages, high inrush currents can result due to the charging of bulk capacitance that resides across the supply pins of the circuit board. This inrush current, although transient in nature, may be high enough to cause permanent damage to on board components or may cause the system's supply voltages to go out of regulation during the transient period which may result in system failures. The MIC2582 and MIC2583 act as a controller for external N-Channel MOSFET devices in which the gate drive is controlled to provide inrush current limiting and output voltage slew rate control during hot plug insertions. Power Supply VCC is the supply input to the MIC2582/83 controller with a voltage range of 2.3V to 13.2V. The VCC input can withstand transient spikes up to 20V. In order to ensure stability of the supply voltage, a minimum 0.47F capacitor from VCC to ground is recommended. Alternatively, a low pass filter, shown in the typical application circuit (see Figure 1), can be used to eliminate high frequency oscillations as well as help suppress transient spikes. Also, due to the existence of an undetermined amount of parasitic inductance in the absence of bulk capacitance along the supply path, placing a Zener diode at the VCC of the controller to ground in order to provide external supply transient protection is strongly recommended for relatively high current applications (3A). See Figure 1. Start-Up Cycle
Supply Contact Delay
(2)
where VTRIPSLOW is the current limit slow trip threshold found in the electrical table and RSENSE is the selected value that will set the desired current limit. There are two basic start-up modes for the MIC2582/83: 1) Start-up dominated by load capacitance and 2) start-up dominated by total gate capacitance. The magnitude of the inrush current delivered to the load will determine the dominant mode. If the inrush current is greater than the programmed current limit (ILIM), then load capacitance is dominant. Otherwise, gate capacitance is dominant. The expected inrush current may be calculated using the following equation:
INRUSH IGATE x
CLOAD C 17A x LOAD CGATE CGATE
(3)
where IGATE is the GATE pin pull-up current, CLOAD is the load capacitance, and CGATE is the total GATE capacitance (CISS of the external MOSFET and any external capacitor connected from the MIC2582/83 GATE pin to ground).
Load Capacitance Dominated Start-Up
During a hot insert of a PC board into a backplane or when the supply (VCC) is powered up, as the voltage at the ON pin rises above its threshold (1.24V typical), the MIC2582/83 first checks that both supply voltages are above their respective UVLO thresholds. If so, the device is enabled and an internal 2.5A current source begins charging capacitor CPOR to 0.3V to initiate a start-up sequence. Once the start-up delay (tSTART) elapses, the CPOR pin is pulled immediately to ground and a 17A current source begins charging the GATE output to drive the external MOSFET that switches VIN to VOUT. The programmed contact start-up delay is calculated using the following equation:
In this case, the load capacitance (CLOAD) is large enough to cause the inrush current to exceed the programmed current limit but is less than the fast-trip threshold (or the fast-trip threshold is disabled, `M' option). During start-up under this condition, the load current is regulated at the programmed current limit value (ILIM) and held constant until the output voltage rises to its final value. The output slew rate and equivalent GATE voltage slew rate is computed by the following equation:
Output Voltage Slew Rate, dVOUT /dt =
ILIM CLOAD
(4)
t START = CPOR x
VSTART ICPOR
0.12 x CPOR (F) (1)
where the start-up delay timer threshold (VSTART) is 0.3V, and the Power-On Reset timer current (ICPOR) is 2.5A. See Table 2 for some typical supply contact start-up delays using several standard value capacitors. As the GATE voltage continues ramping toward its final value (VCC + VGS) at a defined slew rate (See Load Capacitance/Gate Capacitance Dominated Startup sections), a second CPOR timing cycle begins if: 1)/FAULT is high and 2)CFILTER is low (i.e., not an overvoltage, undervoltage lockout, or overcurrent state). This second timing cycle (tPOR) begins when the voltage at the FB pin exceeds its threshold (VFB). This condition indicates that the output voltage is valid. See Figure 3 in the Timing Diagrams. When the power April 2003 13
where ILIM is the programmed current limit value. Consequently, the value of CFILTER must be selected to ensure that the overcurrent response time, tOCSLOW, exceeds the time needed for the output to reach its final value. For example, given a MOSFET with an input capacitance CISS = CGATE = 4700pF, CLOAD is 2200F, and ILIM is set to 6A with a 12V input, then the load capacitance dominates as determined by the calculated INRUSH > ILIM. Therefore, the output voltage slew rate determined from Equation 4 is:
Output Voltage Slew Rate, dVOUT /dt = 6A V = 2.73 2200F ms
and the resulting tOCSLOW needed to achieve a 12V output is approximately 4.5ms. (See Power-On Reset and Overcurrent Timer Delays section to calculate tOCSLOW) MIC2582/MIC2583
MIC2582/MIC2583
GATE Capacitance Dominated Start-Up
Micrel
charges capacitor CPOR. Once the CPOR pin voltage reaches 1.24V, the time period tPOR elapses as the CPOR pin is pulled to ground and the /POR pin goes HIGH. If the voltage at FB drops below VFB for more than 10s, the /POR pin resets for at least one timing cycle defined by tPOR (See Applications Information for an example). Power-On Reset and Overcurrent Timer Delays The Power-On Reset delay, tPOR, is the time period for the /POR pin to go HIGH once the voltage at the FB pin exceeds the power-good threshold (VFB). A capacitor connected to CPOR sets the interval and is determined by using Equation 1 with VTH substituted for VSTART. The resulting equation becomes:
In this case, the value of the load capacitance relative to the GATE capacitance is small enough such that the load current during start-up never exceeds the current limit threshold as determined by Equation 3. The minimum value of CGATE that will ensure that the current limit is never exceeded is given by the equation below:
I CGATE (min) = GATE x CLOAD ILIM
(5)
where CGATE is the summation of the MOSFET input capacitance (CISS) and the value of the external capacitor connected to the GATE pin of the MIC2582/83 to ground. Once CGATE is determined, use the following equation to determine the output slew rate for gate capacitance dominated start-up.
tPOR = CPOR x
VTH ICPOR
0.5 x CPOR (F)
(7)
dVOUT /dt =
IGATE CGATE
IGATE = 17A
(6)
Table 1 depicts the output slew rate for various values of CGATE.
CGATE 0.001F 0.01F 0.1F 1F dVOUT/dt 17V/ms 1.7V/ms 0.17V/ms 0.017V/ms
Table 1. Output Slew Rate Selection for GATE Capacitance Dominated Start-Up Current Limiting and Dual-Level Circuit Breaker Many applications will require that the inrush and steady state supply current be limited at a specific value in order to protect critical components within the system. Connecting a sense resistor between the VCC and SENSE pins sets the nominal current limit value of the MIC2582/83 and the current limit is calculated using Equation 2. The MIC2582/83 also features a dual-level circuit breaker triggered via 50mV and 100mV current limit thresholds sensed across the VCC and SENSE pins. The first level of the circuit breaker functions as follows. For the MIC2583/83R, once the voltage sensed across these two pins exceeds 50mV, the overcurrent timer, its duration set by capacitor CFILTER, starts to ramp the voltage at CFILTER using a 6.5A constant current source. If the voltage at CFILTER reaches the overcurrent timer threshold (VTH) of 1.24V, then CFILTER immediately returns to ground as the circuit breaker trips and the GATE output is immediately shut down. The default overcurrent time period for the MIC2582/83 is 5s. For the second level, if the voltage sensed across VCC and SENSE exceeds 100mV at any time, the circuit breaker trips and the GATE shuts down immediately, bypassing the overcurrent time period. To disable current limit and circuit breaker operation, tie the SENSE and VCC pins together and the CFILTER (MIC2583/83R) pin to ground. Output Undervoltage Detection The MIC2582/83 employ output undervoltage detection by monitoring the output voltage through a resistive divider connected at the FB pin. During turn on, while the voltage at the FB pin is below the threshold (VFB), the /POR pin is asserted low. Once the FB pin voltage crosses VFB, a 2.5A current source MIC2582/MIC2583 14
where the Power-On Reset threshold (VTH) and timer current (ICPOR) are typically 1.24V and 2.5A, respectively. For the MIC2583/83R, a capacitor connected to CFILTER is used to set the timer which activates the circuit breaker during overcurrent conditions. When the voltage across the sense resistor exceeds the slow trip current limit threshold of 50mV, the overcurrent timer begins to charge for a time period (tOCSLOW), determined by CFILTER. When no capacitor is connected to CFILTER and for the MIC2582, tOCSLOW defaults to 5s. If tOCSLOW elapses, then the circuit breaker is activated and the GATE output is immediately pulled to ground. For the MIC2583/83R, the following equation is used to determine the overcurrent timer period, tOCSLOW.
t OCSLOW = CFILTER x
VTH ITIMER
0.19 x CFILTER (F) (8)
where VTH, the CFILTER timer threshold, is 1.24V and ITIMER, the overcurrent timer current, is 6.5A. Tables 2 and 3 provide a quick reference for several timer calculations using select standard value capacitors. CPOR 0.01F 0.02F 0.033F 0.05F 0.1F 0.33F 0.47F 1F CFILTER 680pF 2200pF 4700pF 8200pF 0.033F 0.1F 0.22F 0.47F tSTART 1.2ms 2.4ms 4ms 6ms 12ms 40ms 56ms 120ms tPOR 5ms 10ms 16.5ms 25ms 50ms 165ms 235ms 500ms tOCSLOW 130s 420s 900s 1.5ms 6ms 19ms 42ms 90ms
Table 2. Selected Power-On Reset and Start-Up Delays
Table 3. Selected Overcurrent Timer Delays April 2003
MIC2582/MIC2583
Micrel
V OUT(Good) R5 = R6 - 1 VFB(MAX)
Applications Information
Output Undervoltage Detection For output undervoltage detection, the first consideration is to establish the output voltage level that indicates "power is good." For this example, the output value for which a 12V supply will signal "good" is 11V. Next, consider the tolerances of the input supply and FB threshold (VFB). For this example, the 12V supply varies 5%, thus the resulting output voltage may be as low as 11.4V and as high as 12.6V. Additionally, the FB threshold has 50mV tolerance and may be as low as 1.19V and as high as 1.29V. Thus, to determine the values of the resistive divider network (R5 and R6) at the FB pin, shown in the typical application circuit on page 1, use the following iterative design procedure. 1) Choose R6 so as to limit the current through the divider to approximately 100A or less.
(9.1)
where VFB(MAX) = 1.29V, VOUT(Good) = 11V, and R6 is 12.4k. Substituting these values into Equation 9.1 now yields R5 = 93.33k. A standard 93.1k 1% is selected. Now, consider the 11.4V minimum output voltage, the lower tolerance for R6 and higher tolerance for R5, 12.28k and 94.03k, respectively. With only 11.4V available, the voltage sensed at the FB pin exceeds VFB(MAX), thus the /POR and PWRGD (MIC2583/83R) signals will transition from LOW to HIGH, indicating "power is good" given the worse case tolerances of this example. PCB Connection Sense There are several configuration options for the MIC2582/83's ON pin to detect if the PCB has been fully seated in the backplane before initiating a start-up cycle. In the typical applications circuit, the MIC2582/83 is mounted on the PCB with a resistive divider network connected to the ON pin. R2 is connected to a short pin on the PCB edge connector. Until the connectors mate, the ON pin is held low which keeps the GATE output charge pump off. Once the connectors mate, the resistor network is pulled up to the input supply, 12V in this example, and the ON pin voltage exceeds its threshold (VON) of 1.24V and the MIC2582/83 initiates a start-up cycle. In Figure 6, the connection sense consisting of a discrete logic-level MOSFET and a few resistors allows for interrupt
1.29V 12.9k . 100A 100A R6 is chosen as 12.4k 1%. 2) Next, determine R5 using the output "good" voltage of 11V and the following equation: R6
(R5 + R6) VOUT(Good) = VFB R6 (9)
VFB(MAX)
Using some basic algebra and simplifying Equation 9 to isolate R5, yields:
Backplane PCB Edge Connector Connector
VIN 5V
Long Pin
3
RSENSE 0.010 1 5% 2 C1 1F
4
Q1 Si7860DP (PowerPAK" SO-8) CLOAD 220 F
VOUT 5V@3A
**R8 10 R5 20k R4 20k
3 16 15
VCC ON
SENSE GATE
14
R1 33k
/ON_OFF
R3 100
R2 *Q2 33k
13 12
C2 0.01 F
R6 27.4k 1%
MIC2583 Short Pin PCB Connection Sense
DIS FB
VIN
R9 20
/FAULT
Medium or Short Pin
11
R7 10.5k 1%
/FAULT CPOR
4
GND
7,8
/POR
1
Downstream Signal
GND
Long Pin
C3 0.05 F Undervoltage (Output) = 4.45V /POR Delay = 25ms START-UP Delay = 6ms *Q2 is TN0201T (SOT-23) **R8 is optional for noise filtering Additional pins omitted for clarity.
Figure 6. PCB Connection Sense with ON/OFF Control April 2003 15 MIC2582/MIC2583
MIC2582/MIC2583
control from the processor or other signal controller to shut off the output of the MIC2582/83. R4 pulls the GATE of Q2 to VIN and the ON pin is held low until the connectors are fully mated. Once the connectors fully mate, a logic LOW at the /ON_OFF signal turns Q2 off and allows the ON pin to pull up above its threshold and initiate a start-up cycle. Applying a logic HIGH at the /ON_OFF signal will turn Q2 on and short the ON pin of the MIC2582/83 to ground which turns off the GATE output charge pump. Higher UVLO Setting Once a PCB is inserted into a backplane (power supply), the internal UVLO circuit of the MIC2582/83 holds the GATE output charge pump off until VCC exceeds 2.2V. If VCC falls below 2.1V, the UVLO circuit pulls the GATE output to ground and clears the overvoltage and/or current limit faults. For a higher UVLO threshold, the circuit in Figure 7 can be used to delay the output MOSFET from switching on until the desired input voltage is achieved. The circuit allows the charge pump 5V Switch with 3.3V Supply Generation
Micrel
The MIC2582/83 can be configured to switch a primary supply while generating a secondary regulated voltage rail. The circuit in Figure 8 enables the MIC2582 to switch a 5V supply while also providing a 3.3V low dropout regulated supply with only a few added external components. Upon enabling the MIC2582, the GATE output voltage increases and thus the 3.3V supply also begins to ramp. As the 3.3V output supply crosses 3.3V, the FB pin threshold is also exceeded which triggers the power-on reset comparator. The /POR pin goes HIGH, turning on transistor Q3 which lowers the voltage on the gate of MOSFET Q2. The result is a regulated 3.3V supply with the gate feedback loop of Q2 compensated by capacitor C3 and resistors R4 and R5. For MOSFET Q2, special consideration must be given to the power dissipation capability of the selected MOSFET as 1.5V to 2V will drop across the device during normal operation in this application. Therefore, the device is susceptible to overheating dependent upon the current requirements for the regulated output. In this example, the power dissipated by Q2 is approximately 1W. However, a substantial amount of power will be generated with higher current requirements and/or conditions. As a general guideline, expect the ambient temperature within the power supply box to exceed the maximum operating ambient temperature of the system environment by approximately 20C. Given the MOSFET's R(J-A) and the expected power dissipated by the MOSFET, an approximation for the junction temperature at which the device will operate is obtained as follows: TJ = (PD x R(J-A)) + TA' (10) where TA'=TA(MAX OPERATING) + 20C. As a precaution, the implementation of additional copper heat sinking is highly recommended for the area under/around the MOSFET. For additional information on MOSFET thermal considerations, please see MOSFET Selection text and subsequent sections.
RSENSE 0.010 1 5% 2 D1 (18V) R1 332k 1% C1 1F
3 4
R1 x 1.24V . The GATE to remain off until VIN exceeds 1 + R2
drive output will be shut down when VIN falls below
R1 x 1.19V . In the example circuit (Figure 7), the rising 1+ R2 UVLO threshold is set at approximately 9.5V and the falling UVLO threshold is established as 9.1V. The circuit consists of an external resistor divider at the ON pin that keeps the GATE output charge pump off until the voltage at the ON pin exceeds its threshold (VON) and after the start-up timer elapses.
VIN 12V
Q1 IRF7822 (SO-8) CLOAD 220F
7
VOUT 12V@4A
8
R3 10 GATE
6
VCC
SENSE
R4 133k 1%
2
C2 0.01F ON MIC2582 FB GND
4 5
R2 49.9k 1%
R5 16.2k 1%
Undervoltage Lockout Threshold (rising) = 9.5V Undervoltage Lockout Threshold (falling) = 9.1V Undervoltage (Output) = 11.4V Additional pins omitted for clarity.
Figure 7. Higher UVLO Setting MIC2582/MIC2583 16 April 2003
MIC2582/MIC2583
Q2 Si4876DY (SO-8) Backplane PCB Edge Connector Connector Q1 Si4876DY (SO-8)
4
Micrel
VIN 5V
D1 (9V)
Long Pin
1 2 3
C6 100 F
VOUT 3.3V@0.5A VOUT 5V@3.5A
C1 0.47 F
RSENSE 0.010 2%
C5 330 F R2 10
7
R3 10
8
R1 47k
VCC
2
SENSE GATE
6
R4 1.2M C2 0.022 F C3 4700pF R5 510k
ON
MIC2582 /POR CPOR FB GND
4 1 5
VIN
R8 20k R9 750 Q3 PN2222 R6 20k 1% C4 0.1 F
Open Circuit Short Pin
3
R7 11.8k 1%
GND
Long Pin Undervoltage (Output) = 3.3V All resistors 5% unless specified otherwise
Figure 8. 5V Switch/3.3V LDO Application
Auto-Restart - MIC2583R The MIC2583R provides an auto-restart function. Upon an overcurrent fault condition such as a short circuit, the MIC2583R initially shuts off the GATE output. The MIC2583R attempts to restart with a 12A charge current at a preset 10% duty cycle until the fault condition is removed. The interval between auto-retry attempts is set by capacitor CFILTER. Sense Resistor Selection The MIC2582 and MIC2583 use a low-value sense resistor to measure the current flowing through the MOSFET switch (and therefore the load). This sense resistor is nominally set at 50mV/ILOAD(CONT). To accommodate worst-case tolerances for both the sense resistor (allow 3% over time and temperature for a resistor with 1% initial tolerance) and still supply the maximum required steady-state load current, a slightly more detailed calculation must be used. The current limit threshold voltage (i.e., the "trip point") for the MIC2582/83 may be as low as 42mV, which would equate to a sense resistor value of 42mV/ILOAD(CONT). Carrying the numbers through for the case where the value of the sense resistor is 3% high yields:
RSENSE(MAX) =
Once the value of RSENSE has been chosen in this manner, it is good practice to check the maximum ILOAD(CONT) which the circuit may let through in the case of tolerance buildup in the opposite direction. Here, the worst-case maximum current is found using a 59mV trip voltage and a sense resistor that is 3% low in value. The resulting equation is:
ILOAD(CONT,MAX) =
(0.97)(RSENSE(NOM) )
59mV
=
60.8mV RSENSE(NOM) (12)
As an example, if an output must carry a continuous 2A without nuisance trips occurring, Equation 11 yields: RSENSE(MAX) = 40.8mV = 20.4m . The next lowest 2A standard value is 20m. At the other set of tolerance extremes for the output in question, ILOAD(CONT,MAX) =
(1.03)(ILOAD(CONT) )
42mV
=
40.8mV ILOAD(CONT) (11)
60.8mV = 3.04A , approximately 3A. 20.0m Knowing this final datum, we can determine the necessary wattage of the sense resistor using P = I2R, where I will be ILOAD(CONT, MAX), and R will be (0.97)(RSENSE(NOM)). These numbers yield the following: PMAX = (3A)2 (19.4m) = 0.175W. In this example, a 1/4W sense resistor is sufficient.
April 2003
17
MIC2582/MIC2583
MIC2582/MIC2583
MOSFET Selection Selecting the proper external MOSFET for use with the MIC2582/83 involves three straightforward tasks: * Choice of a MOSFET which meets minimum voltage requirements. * Selection of a device to handle the maximum continuous current (steady-state thermal issues). * Verify the selected part's ability to withstand any peak currents (transient thermal issues). MOSFET Voltage Requirements The first voltage requirement for the MOSFET is easily stated: the drain-source breakdown voltage of the MOSFET must be greater than VIN(MAX). For instance, a 12V input may reasonably be expected to see high-frequency transients as high as 18V. Therefore, the drain-source breakdown voltage of the MOSFET must be at least 19V. For ample safety margin and standard availability, the closest value will be 20V. The second breakdown voltage criterion that must be met is a bit subtler than simple drain-source breakdown voltage, but
Micrel
is not hard to meet. In MIC2582/83 applications, the gate of the external MOSFET is driven up to approximately 19.5V by the internal output MOSFET (again, assuming 12V operation). At the same time, if the output of the external MOSFET (its source) is suddenly subjected to a short, the gate-source voltage will go to (19.5V - 0V) = 19.5V. This means that the external MOSFET must be chosen to have a gate-source breakdown voltage of 20V or more, which is an available standard maximum value. However, if operation is at or above 13V, the 20V gate-source maximum will likely be exceeded. As a result, an external Zener diode clamp should be used to prevent breakdown of the external MOSFET when operating at voltages above 8V. A Zener diode with 10V rating is recommended as shown in Figure 9. At the present time, most power MOSFETs with a 20V gate-source voltage rating have a 30V drain-source breakdown rating or higher. As a general tip, choose surface-mount devices with a drainsource rating of 30V as a starting point. Finally, the external gate drive of the MIC2582/83 requires a low-voltage logic level MOSFET when operating at voltages lower than 3V. There are 2.5V logic level MOSFETs available. Please see Table 4 MOSFET and Sense Resistor Vendors for suggested manufacturers.
VIN 12V D1 (18V) R1 33k
3
RSENSE 0.006 1 5% 2
4
Q1 IRF7822 (SO-8)
*D2 1N5240B 10V CLOAD 220F
VOUT 12V@6A
C1 1F R3 10 GATE
6
8
7
VCC
SENSE
R4 100k 1%
2
C2 0.01F ON MIC2582 FB
5
VIN R6 47k R5 13.3k 1%
R2 33k CPOR
3
GND
4
/POR
1
DOWNSTREAM SIGNAL
C3 0.05F Undervoltage (Output) = 11.0V /POR Delay = 25ms START-UP Delay = 6ms *Recommended for MOSFETs with gate-source breakdown of 20V or less for catastrophic output short circuit protection. (IRF7822 VGS(MAX) = 12V)
Figure 9. Zener Clamped MOSFET Gate
MIC2582/MIC2583
18
April 2003
MIC2582/MIC2583
MOSFET Steady-State Thermal Issues The selection of a MOSFET to meet the maximum continuous current is a fairly straightforward exercise. First, arm yourself with the following data: * The value of ILOAD(CONT, MAX.) for the output in question (see Sense Resistor Selection). * The manufacturer's data sheet for the candidate MOSFET. * The maximum ambient temperature in which the device will be required to operate. * Any knowledge you can get about the heat sinking available to the device (e.g., can heat be dissipated into the ground plane or power plane, if using a surface-mount part? Is any airflow available?). The data sheet will almost always give a value of on resistance given for the MOSFET at a gate-source voltage of 4.5V, and another value at a gate-source voltage of 10V. As a first approximation, add the two values together and divide by two to get the on-resistance of the part with 8V of enhancement. Call this value RON. Since a heavily enhanced MOSFET acts as an ohmic (resistive) device, almost all that's required to determine steady-state power dissipation is to calculate I2R. The one addendum to this is that MOSFETs have a slight increase in RON with increasing die temperature. A good approximation for this value is 0.5% increase in RON per C rise in junction temperature above the point at which RON was initially specified by the manufacturer. For instance, if the selected MOSFET has a calculated RON of 10m at a TJ = 25C, and the actual junction temperature ends up at 110C, a good first cut at the operating value for RON would be: RON 10m[1 + (110 - 25)(0.005)] 14.3m The final step is to make sure that the heat sinking available to the MOSFET is capable of dissipating at least as much power (rated in C/W) as that with which the MOSFET's performance was specified by the manufacturer. Here are a few practical tips: 1. The heat from a surface-mount device such as an SO-8 MOSFET flows almost entirely out of the drain leads. If the drain leads can be soldered down to one square inch or more, the copper will act as the heat sink for the part. This copper must be on the same layer of the board as the MOSFET drain. 2. Airflow works. Even a few LFM (linear feet per minute) of air will cool a MOSFET down substantially. If you can, position the MOSFET(s) near the inlet of a power supply's fan, or the outlet of a processor's cooling fan. 3. The best test of a surface-mount MOSFET for an application (assuming the above tips show it to be a likely fit) is an empirical one. Check the MOSFET's temperature in the actual layout of the expected final circuit, at full operating
Micrel
current. The use of a thermocouple on the drain leads, or infrared pyrometer on the package, will then give a reasonable idea of the device's junction temperature. MOSFET Transient Thermal Issues Having chosen a MOSFET that will withstand the imposed voltage stresses, and the worse case continuous I2R power dissipation which it will see, it remains only to verify the MOSFET's ability to handle short-term overload power dissipation without overheating. A MOSFET can handle a much higher pulsed power without damage than its continuous dissipation ratings would imply. The reason for this is that, like everything else, thermal devices (silicon die, lead frames, etc.) have thermal inertia. In terms related directly to the specification and use of power MOSFETs, this is known as "transient thermal impedance," or Z(J-A). Almost all power MOSFET data sheets give a Transient Thermal Impedance Curve. For example, take the following case: VIN = 12V, tOCSLOW has been set to 100msec, ILOAD(CONT. MAX) is 2.5A, the slow-trip threshold is 50mV nominal, and the fast-trip threshold is 100mV. If the output is accidentally connected to a 3 load, the output current from the MOSFET will be regulated to 2.5A for 100ms (tOCSLOW) before the part trips. During that time, the dissipation in the MOSFET is given by: P = E x I EMOSFET = [12V-(2.5A)(3)] = 4.5V PMOSFET = (4.5V x 2.5A) = 11.25W for 100msec. At first glance, it would appear that a really hefty MOSFET is required to withstand this sort of fault condition. This is where the transient thermal impedance curves become very useful. Figure 10 shows the curve for the Vishay (Siliconix) Si4410DY, a commonly used SO-8 power MOSFET. Taking the simplest case first, we'll assume that once a fault event such as the one in question occurs, it will be a long time- 10 minutes or more- before the fault is isolated and the channel is reset. In such a case, we can approximate this as a "single pulse" event, that is to say, there's no significant duty cycle. Then, reading up from the X-axis at the point where "Square Wave Pulse Duration" is equal to 0.1sec (=100msec), we see that the Z(J-A) of this MOSFET to a highly infrequent event of this duration is only 8% of its continuous R(J-A). This particular part is specified as having an R(J-A) of 50C/W for intervals of 10 seconds or less. Thus: Assume TA = 55C maximum, 1 square inch of copper at the drain leads, no airflow. Recalling from our previous approximation hint, the part has an RON of (0.0335/2) = 17m at 25C. Assume it has been carrying just about 2.5A for some time. When performing this calculation, be sure to use the highest anticipated ambient temperature (TA(MAX)) in which the MOSFET will be operating as the starting temperature, and find the operating junction temperature increase (TJ) from that point. Then, as shown next, the final junction temperature is found by adding TA(MAX) and TJ. Since this is not a closedform equation, getting a close approximation may take one or
April 2003
19
MIC2582/MIC2583
MIC2582/MIC2583
two iterations, But it's not a hard calculation to perform, and tends to converge quickly. Then the starting (steady-state)TJ is: TJ TA(MAX) + TJ TA(MAX) + [RON + (TA(MAX) - TA)(0.005/C)(RON)] x I2 x R(J-A) TJ 55C + [17m + (55C-25C)(0.005)(17m)] x (2.5A)2 x (50C/W) TJ (55C + (0.122W)(50C/W) 61.1C Iterate the calculation once to see if this value is within a few percent of the expected final value. For this iteration we will start with TJ equal to the already calculated value of 61.1C: TJ TA + [17m + (61.1C-25C)(0.005)(17m)] x (2.5A)2 x (50C/W) TJ ( 55C + (0.125W)(50C/W) 61.27C
Micrel
So our original approximation of 61.1C was very close to the correct value. We will use TJ = 61C. Finally, add (11.25W)(50C/W)(0.08) = 45C to the steadystate TJ to get TJ(TRANSIENT MAX.) = 106C. This is an acceptable maximum junction temperature for this part. PCB Layout Considerations Because of the low values of the sense resistors used with the MIC2582/83 controllers, special attention to the layout must be used in order for the device's circuit breaker function to operate properly. Specifically, the use of a 4-wire Kelvin connection to accurately measure the voltage across RSENSE is highly recommended. Kelvin sensing is simply a means of making sure that any voltage drops in the power traces connecting to the resistors does not get picked up by the traces themselves. Additionally, these Kelvin connections should be isolated from all other signal traces to avoid introducing noise onto these sensitive nodes. Figure 11 illustrates a recommended, single layer layout for the RSENSE,
Normalized Thermal Transient Impedance, Junction-to-Ambient
2 1 Duty Cycle = 0.5
Normalized Effective Transient Thermal Impedance
0.2
Notes:
0.1 0.1 0.05
PDM t1 t2 t1 1. Duty Cycle, D = t2 2. Per Unit Base = RthJA = 50 C/W
0.02 Single Pulse 0.01 10-4 10-3 10-2 10-1 Square Wave Pulse Duration (sec) 1
3. TJM - TA = PDMZthJA(t) 4. Surface Mounted
10
30
Figure 10. Transient Thermal Impedance
Current Flow to the Load *SENSE RESISTOR (2512)
D D
Current Flow to the Load *POWER MOSFET (SO-8)
G S S S
W
D D
W
**RGATE 93.1k 1%
8 7 6 5
MIC2582-JBM
VCC
SENSE
GATE
12.4k 1% **CGATE
CPOR
/POR
1
2
ON
3
4
Current Flow to the Load
**CPOR
W
DRAWING IS NOT TO SCALE *See Table 4 for part numbers and vendors. **Optional components. Trace width (W) guidelines given in "PCB Layout Recommendations" section of the datasheet.
Figure 11. Recommended PCB Layout for Sense Resistor, Power MOSFET, and Feedback Network MIC2582/MIC2583 20 April 2003
GND
FB
MIC2582/MIC2583
Power MOSFET, timer(s), and feedback network connections. The feedback network resistor values are selected for a 12V application. Many hot swap applications will require load currents of several amperes. Therefore, the power (VCC and Return) trace widths (W) need to be wide enough to allow the current to flow while the rise in temperature for a given copper plate (e.g., 1oz. or 2oz.) is kept to a maximum of 10C~25C. Also, these traces should be as short as possible in order to minimize the IR drops between the input and the load. For a starting point, there are many trace width calculation tools available on the web such as the following link: http://www.aracnet.com/cgi-usr/gpatrick/trace.pl
Micrel
Finally, the use of plated-through vias will be needed to make circuit connections to power and ground planes when utilizing multi-layer PC boards. MOSFET and Sense Resistor Vendors Device types and manufacturer contact information for power MOSFETs and sense resistors is provided in Table 4. Some of the recommended MOSFETs include a metal heat sink on the bottom side of the package. The recommended trace for the MOSFET Gate of Figure 11 must be redirected when using MOSFETs packaged in this style. Contact the device manufacturer for package information.
MOSFET Vendors Vishay (Siliconix)
Key MOSFET Type(s) Si4420DY (SO-8 package) Si4442DY (SO-8 package) Si4876DY (SO-8 package) Si7892DP (PowerPAKTM SO-8) IRF7413 (SO-8 package) IRF7457 (SO-8 package) IRF7601 (SO-8 package) FDS6680A (SO-8 package) PH3230 (SOT669-LFPAK) HAT2099H (LFPAK)
Applications* IOUT 10A IOUT = 10-15A, VCC < 3V IOUT 5A, VCC 5V IOUT 15A IOUT 10A IOUT = 10-15A IOUT 5A, VCC < 3V IOUT 10A IOUT 20A IOUT 20A
Contact Information www.siliconix.com (203) 452-5664
International Rectifier
www.irf.com (310) 322-3331 www.fairchildsemi.com (207) 775-8100 www.philips.com www.halsp.hitachi.com (408) 433-1990
Fairchild Semiconductor Philips Hitachi
* These devices are not limited to these conditions in many cases, but these conditions are provided as a helpful reference for customer applications.
Resistor Vendors Vishay (Dale) IRC
Sense Resistors "WSL" Series
Contact Information www.vishay.com/docswsl_30100.pdf (203) 452-5664
"OARS" Series www.irctt.com/pdf_files/OARS.pdf "LR" Series www.irctt.com/pdf_files/LRC.pdf (second source to "WSL") (828) 264-8861 Table 4. MOSFET and Sense Resistor Vendors
April 2003
21
MIC2582/MIC2583
MIC2582/MIC2583
Micrel
Package Information
0.026 (0.65) MAX)
PIN 1
0.157 (3.99) 0.150 (3.81)
DIMENSIONS: INCHES (MM)
0.050 (1.27) TYP
0.020 (0.51) 0.013 (0.33) 0.0098 (0.249) 0.0040 (0.102) 0-8 SEATING PLANE 45 0.010 (0.25) 0.007 (0.18)
0.064 (1.63) 0.045 (1.14)
0.197 (5.0) 0.189 (4.8)
0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.228 (5.79)
8-Pin SOP (M)
PIN 1
0.157 (3.99) 0.150 (3.81)
DIMENSIONS: INCHES (MM)
0.009 (0.2286) REF 0.025 (0.635) BSC 0.0098 (0.249) 0.0040 (0.102)
0.012 (0.30) 0.008 (0.20)
0.0098 (0.249) 0.0075 (0.190)
45
8 0
SEATING 0.0688 (1.748) PLANE 0.0532 (1.351)
0.196 (4.98) 0.189 (4.80)
0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.229 (5.82)
Rev. 04
16-pin QSOP (QS)
MICREL, INC.
TEL
1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA
FAX
+ 1 (408) 944-0800
+ 1 (408) 944-0970
WEB
http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2003 Micrel, Incorporated.
MIC2582/MIC2583
22
April 2003

▲Up To Search▲

Price & Availability of MIC2583R-KBQS

	To Download MIC2583R-KBQS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .